This website uses cookies primarily for visitor analytics. Certain pages will ask you to fill in contact details to receive additional information. On these pages you have the option of having the site log your details for future visits. Indicating you want the site to remember your details will place a cookie on your device. To view our full cookie policy, please click here. You can also view it at any time by going to our Contact Us page.

Sponsored: Electrical safety at work - deciphering the IET Code of Practice

18 March 2013

Jim Wallace of Seaward highlights the main changes included in the new IET Code of Practice for maintaining the safety of electrical equipment in the workplace.

The revised IET Code of Practice for In Service Inspection and Testing of Electrical Equipment is essentially the third step in a process that started with the publication of the Löfstedt Review on health and safety and continued with the HSE’s revised guidance on maintaining portable electrical equipment in low risk environments.

In all cases, concern was expressed that the implied legal requirement for maintaining the safety of electrical appliances was being applied too broadly and disproportionately, resulting in situations of over compliance, particularly in more benign working environments.

The fourth edition of the IET Code of Practice follows this theme by focussing on the importance of taking a proportionate response to ensure that all workplace electrical systems should be maintained to prevent danger, so far as is reasonably practicable, and in line with the requirements of the Electricity at Work Regulations 1989.

The introduction of the new IET Code of Practice is designed to give duty holders more understanding, control and flexibility over how electrical safety at work is maintained.

Whilst this may provide some encouragement for in-house testing where suitably trained and competent staff are available, the new guidance also makes it clear that duty holders can if necessary take advice from the person doing the inspection and testing.

Assessment of Risk
The clear message in the new IET Code is that electrical safety should be based on a more focused and robust approach to assessing the risks posed by electrical appliances. The implication is that only when the risk of using electrical equipment has been assessed and understood can it be managed through a programme of inspection and testing.

In fact the Code has always emphasised that the frequency of inspections and testing should be reviewed on a regular basis after an assessment of the risks associated with the use of a particular appliance.

However, new prominence is given to this approach in the latest document which also reiterates that risk based assessments are the responsibility of the duty holder (which might be the facilities manager, building manager , landlord or other such responsible person), but that a duty holder may enlist the services of a competent person to assist in this process.

It is also highlighted that risk assessments should be reviewed regularly to ensure that any control measures remain effective.

Risk encompasses many factors that can eventually influence a final decision and, for example, should include a full consideration of the environment in which the equipment is being used, the level of user awareness, the equipment construction and type, frequency of use, previous records and type of installation for fixed appliances.

All of the factors used in the risk assessment should culminate in enabling an informed decision to be made on the frequency of any inspections and tests required.

To further reflect the new emphasis on assessment of risk, the IET’s also stresses that its own widely used table on test intervals included in the CoP should be used only as guide to the initial frequencies of inspection and testing.

Labelling and documentation
Duty holders have a legal responsibility to ensure that the electrical equipment in their charge is safe and it is their responsibility to decide whether or not to vary the inspection and test frequencies. However, in doing so, the IET makes it clear that dutyholders can if necessary take advice from the person doing the inspection and testing.

The Code also says it is good practice to ensure that all equipment that requires routine inspection and/or testing is clearly identifiable and labelled. However, in a significant change to existing practices, it is now recommended that the date for re-testing should not be marked on the pass label.

Instead it is advised that the ‘the duty holder should determine the date for the next inspection and/or tests on a risk assessment basis...and record this on their ‘Equipment formal visual and combined inspection test record.’

Clearly, without a visual reminder of any next test due dates, there is likely to be increased reliance on the effective use of electrical equipment asset records and inspection and test data.

Although there is no requirement in the Electricity at Work Regulations 1989 to keep records of equipment and of inspections and tests, the HSE Memorandum of Guidance (HSR25) on these regulations advises that records of maintenance including test results should be kept throughout the working life of equipment.

To help those with responsibility for maintaining electrical safety at work, and introduced in response to the new IET Code, the latest generation Apollo 600 PAT tester is equipped with an on-board risk assessment tool to help determine re-test intervals. The universal nature of this feature, and the inclusion of other safety certification capabilities, effectively converts the tester into a much more versatile safety management tool for the assessment of other workplace safety aids such as fire detection systems, alarms and emergency lighting.

The new Code of Practice should help all those involved in maintaining electrical safety in the workplace to better understand their obligations and use risk assessment to make more informed decisions on the scope of inspection and testing required.

More details at www.apollo600.com


Contact Details and Archive...

Print this page | E-mail this page

RELATED CONTENT...

View more articles
Article image

Next generation LEDS for UK retailer

As part of its commitment to reduce energy consumption and its direct carbon footprint, Next has made the leap from traditional lighting to the latest LED ...
http://www.fsifm.com
PFM


MOST VIEWED...

View more articles
Article image

Why the Law Says You Need a Nappy Bin Disposal Service

At home, parents are used to disposing of their babies’ used nappies the same way they do any other domestic waste - bagging it up and sticking it in the r...
Article image

Young Leader finalists announced by EWL

Four finalists have been announced by the Emerging Workplace Leaders (EWL) within the Young Leader of the Year (YLOTY) category within the PFM Awards 2019....

Benchmarking maintenance

BSRIA has just published this year's operation and maintenance benchmarking report as a guide for building operators to evaluate their performance against ...
Article image

Wireless key safe launched by Orbis Protect

An agreement between leading site protection provider Orbis Protect and the makers of the UK’s most secure smart key safe is set to significantly improve s...
Article image

California law predicted to impact on the wider gig economy

Industry experts are continuing to assess Assembly Bill 5 (AB5) passed by the Senate of the US state of California this week....
Article image

BBC describes SF6 gas as 'electrical industry's dirty secret'

According to a recent BBC report, SF6 is the most powerful greenhouse gas known to humanity and emissions have increased due to raised levels of use for me...